New sampler with constant capacity Air-Cube, for the enviroment samplings with fix emplacement. Suitable for samplings of total dusts, breathable dusts, noxious fumes, scattered gas in the air and chimney’s samplings.

The strong box, made of light and compact aluminium alloy, epoxic painted, allows the use without any problem and in the most severe enviroment conditions. Equipped with a membrane pump with Thomas singlehead with push-buttons compensator able to cover the open inlet flow from 0,2 to 30 liters per minute, able to compensate load losses up to 500 mm/Hg in the range of effective capacity between 0,2 and 24 liters per minute.

This instrument is furnished as controller of temperature end exercise pressure, by-pass for suction flows control and regulation, double fluxmeter (for high and low flows), for the capacity control, volumetric dry meter. The new AirCube can be powered also with an intergrated power-pack of the Power Pack Serie for samplings in places not easily reachable by current plugs, manteining a constant flow for 6 hours at the maximum capacity.

Equipped with an instruction booklet in italian, 150cm silicone pipe for taking (10x18)

Sampler in the Plus version, includes control and management of all the phases through the microprocessor Plus, able to add new characteristics and capacities:

• Electronic management of the sampling with a planning, up to 4 different cycles of sampling with
| self-contained settings expressed in time or volume to sample
• Flow reading on the display in real time during the sampling
• Sampling temperature reading
• Direct atmospheric pressure reading with high precise sensor (opt)
• Reading of set time and remaining time
• The microprocessor Plus records data and times of sampling
| also in case of energy lack and as soon as energy re-stars sampling re-starts from the interruption
| point

All data are recorded in the memory and in the final report all the information joined to the stop and the its length are shown

At the sampling finish it is possible to visualize on the display the following information :
• Temperature at the starting point
• Temperature at the finishing point
• The average Temperature of sampling
• Atmospheric pressure at the starting point
• Atmospheric pressure at the finishing point
• The average pressure during the sampling
• Total sampled volume
• Normalized total volume with choising possibility from 0°,20°, 25°C, with multiple choise to be
| selected with the operator
• The average flow
• Defects during the sampling

The sampler is able to sample with a sequential group of eight-way , scattered dusts and gas.

All data shown on the display can be printed with an external serial printer or exported through a AirNet Software PC.

It is an evolved electronic version able to talk with the capacity measurer IsoFlow 200 for isokinetics takings in real time.


With the EL version, the sampler is able to support:
• Electronic management of the sampling with a programme up to 4 different cycles of sampling with self-contained settings expressed in time and volume to be sampled
• Automatic regulation of the push-button flow with an electronic compensation of the load losses and acoustic warning device in case of losses out of the tollerance values
• Flow reading on the display in real time during the sampling
• Temperature reading on the display during the sampling
• Reading of the atmospheric pressure value directed by a high precision sensor
• Reading of the set-time and of the remaining time of the sampling
• The microprocessor EL records data and times of sampling also in case of energy lack and as soon as energy re-starts sampling re-starts from the interruption point

All data are recorded in the memory and in the final report all the information joined to the stop and the its length are shown

The EL sampler is able to manage in real time an isokinetic sampling if interfaced to the capacity measurer IsoFlow 200 (600/IF200) that controls the isokinetic conditions.

At the sampling finish it is possible to visualize on the display the following information:

• Temperature at the starting point
• Temperature at the finishing point
• The average Temperature of sampling
• Atmospheric pressure at the starting point
• Pressione atmosferica fine campionamento
• Atmospheric pressure at the finishing point
• The average pressure during the sampling
• Total sampled volume
• Normalized total volume with possibility of choise from 0°,20°, 25°C, with multiple choise to be selected with the operator
• The average flow
• Defects during the sampling

The sampler is able to sample with a sequential group of eight-way, scattered dusts and gas.

All data shown on the display can be printed with an external serial printer or exported through a AirNet Software PC In case of sampling in an automatic isokinetic way, all data can be printed.

Similar to the software structure in the EL version, the sampler AirCube Come compensates electronically the load losses manteining a constant flow at the membrane.

All the settings are made for the push-buttons and all the load losses are shown on the display.
The sampler Air-Cube COM is equipped with a membrane suction pump with doublehead and can reach 28 liters/min of capacity with a recycling splash plate inserted.
Samplings are guranteed with battery feed up to 8 hours.

ADDITIONAL CHARACTERISTICS ARE:
• Flow reading in real time on the display during the sampling
• Temperature reading in real time on the display
• Atmospheric pressure value reading driven by a high precision sensor (opt)
• Set time and remaining time reading of the sampling
• The microprocessor COM records data and times of sampling
also in case of energy lack and as soon as energy re-stars sampling re-starts from the interruption point.

All data are recorded in the memory and in the final report all the information joined to the stop and the its length are shown.

At the sampling finish it is possible to visualize on the display the following information:

• Temperature at the starting point
• Temperature at the finishing point
• The average Temperature of sampling
• Atmospheric pressure at the starting point
• Atmospheric pressure at the finishing point
• The average pressure during the sampling
• Total sampled volume
• Normalized total volume with possibility of choise from 0°,20°, 25°C, with multiple choise to be selected with the operator
• The average flow
• Defects during the sampling with a stop and preservation of all the data in case of filter over-loading or with difficulties in manteining a constant flow

The microprocessor COM records data and times of sampling also in case of energy lack and as soon as energy re-stars sampling re-starts from the interruption point.

All data shown on the display can be printed with an external serial printer or exported through a AirNet Software PC.

Complying with the UNI EN 12919:2001 standard
• D.L.n.25 dtd 02/02/2002
• CE referred to : EN 60204-1:1997-12, DIR.89/336/CE